Bakrol, Ahmedabad, India+91 97277 86892
Enquire
Home/Water treatment

Water treatment

Clarification Water Treatment Plant

Coagulation, clarification and filtration selected for source-water characteristics.

Request technical proposal
Conceptual 3D equipment render of Clarification Water Treatment Plant
Clarification Water Treatment Plant — conceptual 3D equipment render. Final configuration follows the approved project design.

3D EQUIPMENT VIEW

Clarification Water Treatment Plant

Explore the equipment arrangement, then read how the system works and review its technical drawings.

Description & drawings Browse equipment renders

Conceptual equipment render. Final dimensions and configuration follow the approved project design.

PRODUCT DESCRIPTION & TECHNICAL DOCUMENTS

How clarification water treatment plant fits your process.

Operating principle

Coagulation, clarification and filtration selected for source-water characteristics.

Gravity separation removes settleable solids. Surface loading, solids characteristics and sludge removal determine the separation arrangement and effective settling area.

Engineering checks

  • Flow range and projected settling area
  • Settling tests and solids loading
  • Weir loading and hydraulic distribution
  • Sludge removal and access

Configuration & equipment

  1. Inlet distribution zone
  2. Settling compartment
  3. Tube / plate modules where selected
  4. Clarified-water collection
  5. Sludge hopper or withdrawal zone
  6. Drain and access provisions

Configuration options are reviewed against the project duty. Supply quantities and final scope are defined in the approved proposal.

Process / operating itemEngineering requirement
Process review 1Lamella plates, tube media or conventional settling are selected for the solids duty.
Operating and maintenanceCheck uniform distribution and water level. Remove accumulated sludge routinely. Inspect modules and collection weirs.
DocumentationProject-specific datasheet, PFD, P&ID, equipment GA, electrical load list and O&M documentation as agreed.

PDF & DRAWING DOWNLOADS

Keep the technical references.

Read the water treatment & ro brochure, or download the process and arrangement drawings below.

Open brochure (PDF) Download PDFProcess drawing ↓Equipment drawing ↓

PROCESS FLOW DIAGRAM

Clarification process

Download drawing (SVG)
Conditioned feed → Coagulation where required → Flocculation where required → Settling zone → Clarified-water collection
Main process Utility / chemical Residual stream Recovery / recycle

Swipe the diagram to view every stage.

Design notes
  • Lamella plates, tube media or conventional settling are selected for the solids duty.

Indicative process overview. Equipment tags identify functional blocks only. Final PFDs, P&IDs, duties, sizes, valves and instruments are developed from the approved project design basis.

EQUIPMENT DRAWINGS

2D layout & exploded component views.

Review the functional arrangement and the components that make up the equipment.

Clarification Water Treatment Plant 2D functional arrangement

Reference drawings are not to scale. Project dimensions, equipment duty, pipe sizes and materials are specified after design review.

Download 2D SVG
Clarification Water Treatment Plant component decomposition reference
Clarification Water Treatment Plant — component decomposition

EXPLODED VIEW

Understand the assembly.

The separated component schematic identifies the main equipment groups. Vendor-specific internal geometry is established during detailed engineering.

  1. Inlet distribution zone
  2. Settling compartment
  3. Tube / plate modules where selected
  4. Clarified-water collection
  5. Sludge hopper or withdrawal zone
  6. Drain and access provisions
Open calculation software Return to catalogue

EXPLORE YOUR DESIGN BASIS

See how operating hours change energy use.

Enter the total running electrical load for this equipment or plant, then adjust its daily running hours.

Illustrative arithmetic using your inputs. These values are not measured plant results or a performance promise.

Daily electricity
80.00 kWh/day
30-day electricity
2400.00 kWh

Energy = electrical kW × running hours. Constant running load; standby load, starting transients and tariff charges are excluded.

Open detailed calculator →

YOUR PROJECT, YOUR DESIGN BASIS

Configure your requirement.

Enter what you know. Leave unavailable values blank for engineering review.

Process inputs

Industry type, effluent flow and operating hours, pH, COD, BOD, TSS, TDS, oil & grease, colour/metals/specific contaminants, equalization pattern, reuse/discharge target and treatability data.

Equipment & execution preferences

Materials are reviewed separately for each component against the fluid chemistry, temperature and service conditions. Preferences are subject to technical suitability and the agreed proposal.

No details are sent until you choose a sending channel.

A solution shaped by your requirements.

Coagulation, clarification and filtration selected for source-water characteristics. The process train is selected from feed-water analysis and the final water specification. Pretreatment protects downstream treatment, while monitoring and cleaning provisions support reliable operation.

What we review

  • Required product flow and operating hours
  • Water source and complete laboratory analysis
  • Feed temperature, pH and fouling indicators
  • Target water quality and intended use
  • Utility availability and plant footprint
  • Pretreatment and cleaning requirements

Capacity, materials, operating conditions and performance are specified after review of your project data. Product images are conceptual visualizations.

From design to operation

Our scope can cover process and mechanical engineering, manufacturing, supply, installation, commissioning and ongoing support. The final proposal clearly defines supplier scope, client interfaces, optional items and exclusions.

APPLICATIONS

Connect equipment to your industry.

Review the application, data requirements and candidate treatment options.

Steel & FoundrySugar & Agro Processing

EXPLORE FURTHER

Related solutions

3D render of a skid-mounted reverse osmosis system with membrane housings, pump and cartridge filterConceptual 3D render

Industrial RO Plant

Pressure-driven membrane treatment to reduce dissolved salts in industrial process water.

Explore
Conceptual 3D equipment render of Two-Pass RO SystemConceptual 3D render

Two-Pass RO System

Two sequential RO passes for applications requiring further polishing of first-pass permeate.

Explore
Conceptual 3D equipment render of High-TDS RO PlantConceptual 3D render

High-TDS RO Plant

RO treatment developed around elevated salinity, scaling limits and feed-water chemistry.

Explore