Bakrol, Ahmedabad, India+91 97277 86892
Enquire
Home/Water treatment

Water treatment

Ultrafiltration (UF) Plant

Membrane filtration for suspended solids and pretreatment or tertiary polishing duties.

Request technical proposal
3D render of vertical ultrafiltration modules, pump and pipework on a steel skid
UF membrane skid — conceptual 3D render

3D EQUIPMENT VIEW

Ultrafiltration (UF) Plant

Explore the equipment arrangement, then read how the system works and review its technical drawings.

Description & drawings Browse equipment renders

Conceptual equipment render. Final dimensions and configuration follow the approved project design.

PRODUCT DESCRIPTION & TECHNICAL DOCUMENTS

How ultrafiltration (uf) plant fits your process.

Operating principle

Membrane filtration for suspended solids and pretreatment or tertiary polishing duties.

A membrane barrier separates suspended matter from the filtrate. Forward filtration, backwash and chemically enhanced cleaning must be evaluated together to establish net production.

Engineering checks

  • Feed turbidity, organics and fouling behaviour
  • Net flux after cleaning and downtime
  • Backwash supply and waste handling
  • Module integrity and vendor operating envelope

Configuration & equipment

  1. Feed pump and protective screen
  2. UF membrane modules
  3. Feed and filtrate headers
  4. Backwash system
  5. Air-scour connections where applicable
  6. Chemical-cleaning circuit
  7. Flow and transmembrane-pressure instruments

Configuration options are reviewed against the project duty. Supply quantities and final scope are defined in the approved proposal.

Process / operating itemEngineering requirement
Process review 1Backwash, air scour and chemical cleaning follow the selected membrane system.
Process review 2Residual streams require collection and an agreed handling route.
Operating and maintenanceTrend transmembrane pressure. Follow approved backwash and cleaning cycles. Perform membrane integrity checks.
DocumentationProject-specific datasheet, PFD, P&ID, equipment GA, electrical load list and O&M documentation as agreed.

PDF & DRAWING DOWNLOADS

Keep the technical references.

Read the water treatment & ro brochure, or download the process and arrangement drawings below.

Open brochure (PDF) Download PDFProcess drawing ↓Equipment drawing ↓

PROCESS FLOW DIAGRAM

Ultrafiltration process

Download drawing (SVG)
Feed storage → Feed pump & strainer → UF membrane modules → Filtrate collection → Downstream treatment / use
Main process Utility / chemical Residual stream Recovery / recycle

Swipe the diagram to view every stage.

Design notes
  • Backwash, air scour and chemical cleaning follow the selected membrane system.
  • Residual streams require collection and an agreed handling route.

Indicative process overview. Equipment tags identify functional blocks only. Final PFDs, P&IDs, duties, sizes, valves and instruments are developed from the approved project design basis.

EQUIPMENT DRAWINGS

2D layout & exploded component views.

Review the functional arrangement and the components that make up the equipment.

Ultrafiltration (UF) Plant 2D functional arrangement

Reference drawings are not to scale. Project dimensions, equipment duty, pipe sizes and materials are specified after design review.

Download 2D SVG
Ultrafiltration (UF) Plant component decomposition reference
Ultrafiltration (UF) Plant — component decomposition

EXPLODED VIEW

Understand the assembly.

The separated component schematic identifies the main equipment groups. Vendor-specific internal geometry is established during detailed engineering.

  1. Feed pump and protective screen
  2. UF membrane modules
  3. Feed and filtrate headers
  4. Backwash system
  5. Air-scour connections where applicable
  6. Chemical-cleaning circuit
  7. Flow and transmembrane-pressure instruments
Open calculation software Return to catalogue

EXPLORE YOUR DESIGN BASIS

See how operating hours change energy use.

Enter the total running electrical load for this equipment or plant, then adjust its daily running hours.

Illustrative arithmetic using your inputs. These values are not measured plant results or a performance promise.

Daily electricity
80.00 kWh/day
30-day electricity
2400.00 kWh

Energy = electrical kW × running hours. Constant running load; standby load, starting transients and tariff charges are excluded.

Open detailed calculator →

YOUR PROJECT, YOUR DESIGN BASIS

Configure your requirement.

Enter what you know. Leave unavailable values blank for engineering review.

Process inputs

Required flow, operating hours, feed source, full water analysis, temperature, target product quality, recovery target, pretreatment, cleaning philosophy, automation, MOC and utility constraints.

Technologies you would like to discuss

Select candidates for review. This does not establish a treatment sequence.

Equipment & execution preferences

Materials are reviewed separately for each component against the fluid chemistry, temperature and service conditions. Preferences are subject to technical suitability and the agreed proposal.

No details are sent until you choose a sending channel.

A solution shaped by your requirements.

Membrane filtration for suspended solids and pretreatment or tertiary polishing duties. The process train is selected from feed-water analysis and the final water specification. Pretreatment protects downstream treatment, while monitoring and cleaning provisions support reliable operation.

What we review

  • Required product flow and operating hours
  • Water source and complete laboratory analysis
  • Feed temperature, pH and fouling indicators
  • Target water quality and intended use
  • Utility availability and plant footprint
  • Pretreatment and cleaning requirements

Capacity, materials, operating conditions and performance are specified after review of your project data. Product images are conceptual visualizations.

From design to operation

Our scope can cover process and mechanical engineering, manufacturing, supply, installation, commissioning and ongoing support. The final proposal clearly defines supplier scope, client interfaces, optional items and exclusions.

APPLICATIONS

Connect equipment to your industry.

Review the application, data requirements and candidate treatment options.

Textile Dyeing & PrintingElectronics & High-Purity ManufacturingLaundry & Commercial Washing

EXPLORE FURTHER

Related solutions

3D render of a skid-mounted reverse osmosis system with membrane housings, pump and cartridge filterConceptual 3D render

Industrial RO Plant

Pressure-driven membrane treatment to reduce dissolved salts in industrial process water.

Explore
Conceptual 3D equipment render of Two-Pass RO SystemConceptual 3D render

Two-Pass RO System

Two sequential RO passes for applications requiring further polishing of first-pass permeate.

Explore
Conceptual 3D equipment render of High-TDS RO PlantConceptual 3D render

High-TDS RO Plant

RO treatment developed around elevated salinity, scaling limits and feed-water chemistry.

Explore