Bakrol, Ahmedabad, India+91 97277 86892
Enquire
Home/Wastewater treatment

Wastewater treatment

Flocculator

Controlled mixing for floc formation following verified coagulation conditions.

Request technical proposal
Conceptual 3D equipment render of Flocculator
Flocculator — conceptual 3D equipment render. Final configuration follows the approved project design.

3D EQUIPMENT VIEW

Flocculator

Explore the equipment arrangement, then read how the system works and review its technical drawings.

Description & drawings Browse equipment renders

Conceptual equipment render. Final dimensions and configuration follow the approved project design.

PRODUCT DESCRIPTION & TECHNICAL DOCUMENTS

How flocculator fits your process.

Operating principle

Controlled mixing for floc formation following verified coagulation conditions.

Mixing distributes chemicals or maintains suspension within the process compartment. Impeller type, mixing intensity, fluid properties and mechanical loads govern selection.

Engineering checks

  • Fluid viscosity, density and solids
  • Tank geometry and mixing objective
  • Shaft deflection, critical speed and support loads
  • Materials and seal requirements

Configuration & equipment

  1. Drive motor and gearbox as selected
  2. Mounting bridge / support
  3. Shaft and coupling
  4. Impeller assembly
  5. Process tank / compartment
  6. Access and mechanical guards

Configuration options are reviewed against the project duty. Supply quantities and final scope are defined in the approved proposal.

Process / operating itemEngineering requirement
Process review 1Mixing, pH control or chemical addition is included only where required by the selected process duty.
Operating and maintenanceInspect alignment and vibration. Check lubrication and fasteners. Inspect shaft, impeller and supports.
DocumentationProject-specific datasheet, PFD, P&ID, equipment GA, electrical load list and O&M documentation as agreed.

PDF & DRAWING DOWNLOADS

Keep the technical references.

Read the wastewater treatment brochure, or download the process and arrangement drawings below.

Open brochure (PDF) Download PDFProcess drawing ↓Equipment drawing ↓

PROCESS FLOW DIAGRAM

Process-vessel connections

Download drawing (SVG)
Incoming stream → Flow distribution → Flocculator → Outlet connection → Next treatment stage
Main process Utility / chemical Residual stream Recovery / recycle

Swipe the diagram to view every stage.

Design notes
  • Mixing, pH control or chemical addition is included only where required by the selected process duty.

Indicative process overview. Equipment tags identify functional blocks only. Final PFDs, P&IDs, duties, sizes, valves and instruments are developed from the approved project design basis.

EQUIPMENT DRAWINGS

2D layout & exploded component views.

Review the functional arrangement and the components that make up the equipment.

Flocculator 2D functional arrangement

Reference drawings are not to scale. Project dimensions, equipment duty, pipe sizes and materials are specified after design review.

Download 2D SVG
Flocculator component decomposition reference
Flocculator — component decomposition

EXPLODED VIEW

Understand the assembly.

The separated component schematic identifies the main equipment groups. Vendor-specific internal geometry is established during detailed engineering.

  1. Drive motor and gearbox as selected
  2. Mounting bridge / support
  3. Shaft and coupling
  4. Impeller assembly
  5. Process tank / compartment
  6. Access and mechanical guards
Open calculation software Return to catalogue

EXPLORE YOUR DESIGN BASIS

See how operating hours change energy use.

Enter the total running electrical load for this equipment or plant, then adjust its daily running hours.

Illustrative arithmetic using your inputs. These values are not measured plant results or a performance promise.

Daily electricity
80.00 kWh/day
30-day electricity
2400.00 kWh

Energy = electrical kW × running hours. Constant running load; standby load, starting transients and tariff charges are excluded.

Open detailed calculator →

CONSTRUCTION OPTIONS

Modular fabrication or civil construction?

Select the treatment process first. Then choose a construction method that fits the site, transport access, project schedule and future expansion.

Prefabricated modular plant

Factory-fabricated process modules connect to agreed site tanks and utilities. Review transport dimensions, lifting access, corrosion protection and maintenance clearances.

For a packaged MBBR example, the anoxic and aerobic compartments have flat floors; a downstream tube-settler compartment can use a sludge hopper. Equalization and treated-water storage may be separate civil tanks.

Explore modular STP / ETP →

Civil construction plant

Site-built basins provide a project-specific layout. Process design must coordinate with soil conditions, groundwater, structural design, hydraulic levels and access for operation.

RCC construction can support several treatment technologies. Civil scope, embedded items, tank lining and mechanical interfaces are defined before execution.

Explore civil STP / ETP →

YOUR PROJECT, YOUR DESIGN BASIS

Configure your requirement.

Enter what you know. Leave unavailable values blank for engineering review.

Process inputs

Industry type, effluent flow and operating hours, pH, COD, BOD, TSS, TDS, oil & grease, colour/metals/specific contaminants, equalization pattern, reuse/discharge target and treatability data.

Equipment & execution preferences

Materials are reviewed separately for each component against the fluid chemistry, temperature and service conditions. Preferences are subject to technical suitability and the agreed proposal.

No details are sent until you choose a sending channel.

A solution shaped by your requirements.

Controlled mixing for floc formation following verified coagulation conditions. Treatment begins with understanding the effluent sources and their variability. Physical, chemical and biological stages are combined as appropriate, followed by polishing and sludge management.

What we review

  • Average daily flow and hourly inflow profile
  • Operating hours and peak-flow conditions
  • BOD, COD, TSS, pH, nutrients and relevant contaminants
  • Reuse or discharge objective
  • Available area, levels and site interfaces
  • Treatability, sludge handling and odour constraints

Capacity, materials, operating conditions and performance are specified after review of your project data. Product images are conceptual visualizations.

From design to operation

Our scope can cover process and mechanical engineering, manufacturing, supply, installation, commissioning and ongoing support. The final proposal clearly defines supplier scope, client interfaces, optional items and exclusions.

APPLICATIONS

Connect equipment to your industry.

Review the application, data requirements and candidate treatment options.

Chemical & PetrochemicalAutomotive & EngineeringPower & Boiler Utilities

EXPLORE FURTHER

Related solutions

Conceptual 3D equipment render of Lamella ClarifierConceptual 3D render

Lamella Clarifier

Inclined-plate clarification selected around settleability and projected surface loading.

Explore
Conceptual 3D equipment render of Tube Settler ClarifierConceptual 3D render

Tube Settler Clarifier

Tube-settler clarification for suitable suspended-solids separation duties.

Explore
Conceptual 3D visualization of dissolved-air flotation unitConceptual 3D render

Dissolved Air Flotation (DAF)

Flotation treatment for suitable suspended solids, fats and floatable contaminants.

Explore