Home/Filtration & dosing

Filtration & dosing

UV Disinfection System

UV treatment selected around water UV transmittance, target organisms and validated equipment.

Request technical proposal

3D render of water treatment vessels and organized skid piping — Treatment-vessel arrangement — conceptual 3D render

SYSTEM VIEW

See the equipment.
Understand the process.

The render illustrates the Softening & media filtration equipment family. Your final arrangement follows the project duty, site layout and approved design.

View process flow Browse the visual gallery

Conceptual 3D visualization · equipment details are illustrative.

PROCESS FLOW DIAGRAM

UV disinfection route

Download SVG

Suitable treated water → Flow & quality monitoring → UV reactor → Outlet monitoring → Final-use connection

Main process Utility / chemical Residual stream Recovery / recycle

Swipe the diagram to view every stage.

Design notes

UV transmittance, flow, fouling and dose validation determine reactor selection.
The diagram does not specify a disinfection performance guarantee.

Indicative process overview. Equipment tags identify functional blocks only. Final PFDs, P&IDs, duties, sizes, valves and instruments are developed from the approved project design basis.

PROCESS & EQUIPMENT DETAILS

How uv disinfection system fits your process.

Operating principle

UV treatment selected around water UV transmittance, target organisms and validated equipment.

Disinfection or oxidation performance depends on contact conditions and water quality. UV uses a validated reactor and exposure dose; ozone or advanced oxidation requires an approved chemical and safety design.

Engineering checks

Water quality and treatment objective
Validated dose or treatability test basis
Required contact and reaction conditions
Interlocks, residual control and operator protection

Configuration & equipment

Feed-quality and flow interface
Reactor / contact assembly
Selected energy or oxidant source
Monitoring and control system
Residual / off-gas handling where applicable
Outlet sampling point

Configuration options are reviewed against the project duty. Supply quantities and final scope are defined in the approved proposal.

Process / operating item	Engineering requirement
Process review 1	UV transmittance, flow, fouling and dose validation determine reactor selection.
Process review 2	The diagram does not specify a disinfection performance guarantee.
Operating and maintenance	Inspect the reactor and clean fouled surfaces. Verify sensors and safety interlocks. Replace consumables according to selected equipment instructions.
Documentation	Project-specific datasheet, PFD, P&ID, equipment GA, electrical load list and O&M documentation as agreed.

EQUIPMENT DRAWINGS

2D layout & exploded component views.

Review the functional arrangement and the components that make up the equipment.

UV Disinfection System 2D functional arrangement

UV Disinfection System component decomposition reference — UV Disinfection System — component decomposition

EXPLODED VIEW

Understand the assembly.

The separated component schematic identifies the main equipment groups. Vendor-specific internal geometry is established during detailed engineering.

Feed-quality and flow interface
Reactor / contact assembly
Selected energy or oxidant source
Monitoring and control system
Residual / off-gas handling where applicable
Outlet sampling point

Open calculation software Return to catalogue

YOUR PROJECT, YOUR DESIGN BASIS

Configure your requirement.

Enter what you know. Leave unavailable values blank for engineering review.

Process inputs

Flow, water quality, target microorganism/oxidation duty, UV transmittance or oxidant demand where applicable, contact time, residual target, safety and automation.

Dose inputsolution strengthdosing flowcontact volumeUV/ozone vendor selectioninterlocksresidual monitoringbypass philosophy

Water source / process stream and intended final use

Technologies you would like to discuss

Select candidates for review. This does not establish a treatment sequence.

UV Disinfection SystemProcess Water Treatment PlantSewage Treatment Plant – MBRPhysico-Chemical ETPTertiary Wastewater Treatment

Equipment & execution preferences

Wetted vessels / tanks — preferred materialProcess piping — preferred materialSkid / structural frame — preferred materialSeals / gaskets — preferred materialAutomation preferenceDuty / standby arrangementInstallation preferencePreferred equipment makes

Location, utilities, access & scope notes

Materials are reviewed separately for each component against the fluid chemistry, temperature and service conditions. Preferences are subject to technical suitability and the agreed proposal.

No details are sent until you choose a sending channel.

A solution shaped by your requirements.

UV treatment selected around water UV transmittance, target organisms and validated equipment. Equipment is selected from the treatment objective, flow profile and fluid characteristics. Media, contact conditions and maintenance provisions are reviewed for the actual duty.

What we review

Design flow and operating hours
Feed solids, particle characteristics and water analysis
Required separation or conditioning duty
Operating pressure and temperature
Cleaning, backwash or replacement requirements
Chemical compatibility and utility constraints

Capacity, materials, operating conditions and performance are specified after review of your project data. Product images are conceptual visualizations.

From design to operation

Our scope can cover process and mechanical engineering, manufacturing, supply, installation, commissioning and ongoing support. The final proposal clearly defines supplier scope, client interfaces, optional items and exclusions.

APPLICATIONS

Connect equipment to your industry.

Review the application, data requirements and candidate treatment options.

Hospitals & Healthcare Packaged Drinking Water

UV Disinfection System

See the equipment. Understand the process.