Bakrol, Ahmedabad, India+91 97277 86892
Enquire
Home/Filtration & dosing

Filtration & dosing

UV Disinfection System

UV treatment selected around water UV transmittance, target organisms and validated equipment.

Request technical proposal
Conceptual 3D equipment render of UV Disinfection System
UV Disinfection System — conceptual 3D equipment render. Final configuration follows the approved project design.

3D EQUIPMENT VIEW

UV Disinfection System

Explore the equipment arrangement, then read how the system works and review its technical drawings.

Description & drawings Browse equipment renders

Conceptual equipment render. Final dimensions and configuration follow the approved project design.

PRODUCT DESCRIPTION & TECHNICAL DOCUMENTS

How uv disinfection system fits your process.

Operating principle

UV treatment selected around water UV transmittance, target organisms and validated equipment.

Disinfection or oxidation performance depends on contact conditions and water quality. UV uses a validated reactor and exposure dose; ozone or advanced oxidation requires an approved chemical and safety design.

Engineering checks

  • Water quality and treatment objective
  • Validated dose or treatability test basis
  • Required contact and reaction conditions
  • Interlocks, residual control and operator protection

Configuration & equipment

  1. Feed-quality and flow interface
  2. Reactor / contact assembly
  3. Selected energy or oxidant source
  4. Monitoring and control system
  5. Residual / off-gas handling where applicable
  6. Outlet sampling point

Configuration options are reviewed against the project duty. Supply quantities and final scope are defined in the approved proposal.

Process / operating itemEngineering requirement
Process review 1UV transmittance, flow, fouling and dose validation determine reactor selection.
Process review 2The diagram does not specify a disinfection performance guarantee.
Operating and maintenanceInspect the reactor and clean fouled surfaces. Verify sensors and safety interlocks. Replace consumables according to selected equipment instructions.
DocumentationProject-specific datasheet, PFD, P&ID, equipment GA, electrical load list and O&M documentation as agreed.

PDF & DRAWING DOWNLOADS

Keep the technical references.

Read the water treatment & ro brochure, or download the process and arrangement drawings below.

Open brochure (PDF) Download PDFProcess drawing ↓Equipment drawing ↓

PROCESS FLOW DIAGRAM

UV disinfection route

Download drawing (SVG)
Suitable treated water → Flow & quality monitoring → UV reactor → Outlet monitoring → Final-use connection
Main process Utility / chemical Residual stream Recovery / recycle

Swipe the diagram to view every stage.

Design notes
  • UV transmittance, flow, fouling and dose validation determine reactor selection.
  • The diagram does not specify a disinfection performance guarantee.

Indicative process overview. Equipment tags identify functional blocks only. Final PFDs, P&IDs, duties, sizes, valves and instruments are developed from the approved project design basis.

EQUIPMENT DRAWINGS

2D layout & exploded component views.

Review the functional arrangement and the components that make up the equipment.

UV Disinfection System 2D functional arrangement

Reference drawings are not to scale. Project dimensions, equipment duty, pipe sizes and materials are specified after design review.

Download 2D SVG
UV Disinfection System component decomposition reference
UV Disinfection System — component decomposition

EXPLODED VIEW

Understand the assembly.

The separated component schematic identifies the main equipment groups. Vendor-specific internal geometry is established during detailed engineering.

  1. Feed-quality and flow interface
  2. Reactor / contact assembly
  3. Selected energy or oxidant source
  4. Monitoring and control system
  5. Residual / off-gas handling where applicable
  6. Outlet sampling point
Open calculation software Return to catalogue

EXPLORE YOUR DESIGN BASIS

See how operating hours change energy use.

Enter the total running electrical load for this equipment or plant, then adjust its daily running hours.

Illustrative arithmetic using your inputs. These values are not measured plant results or a performance promise.

Daily electricity
80.00 kWh/day
30-day electricity
2400.00 kWh

Energy = electrical kW × running hours. Constant running load; standby load, starting transients and tariff charges are excluded.

Open detailed calculator →

YOUR PROJECT, YOUR DESIGN BASIS

Configure your requirement.

Enter what you know. Leave unavailable values blank for engineering review.

Process inputs

Flow, water quality, target microorganism/oxidation duty, UV transmittance or oxidant demand where applicable, contact time, residual target, safety and automation.

Equipment & execution preferences

Materials are reviewed separately for each component against the fluid chemistry, temperature and service conditions. Preferences are subject to technical suitability and the agreed proposal.

No details are sent until you choose a sending channel.

A solution shaped by your requirements.

UV treatment selected around water UV transmittance, target organisms and validated equipment. Equipment is selected from the treatment objective, flow profile and fluid characteristics. Media, contact conditions and maintenance provisions are reviewed for the actual duty.

What we review

  • Design flow and operating hours
  • Feed solids, particle characteristics and water analysis
  • Required separation or conditioning duty
  • Operating pressure and temperature
  • Cleaning, backwash or replacement requirements
  • Chemical compatibility and utility constraints

Capacity, materials, operating conditions and performance are specified after review of your project data. Product images are conceptual visualizations.

From design to operation

Our scope can cover process and mechanical engineering, manufacturing, supply, installation, commissioning and ongoing support. The final proposal clearly defines supplier scope, client interfaces, optional items and exclusions.

APPLICATIONS

Connect equipment to your industry.

Review the application, data requirements and candidate treatment options.

Hospitals & HealthcarePackaged Drinking Water

EXPLORE FURTHER

Related solutions

Conceptual 3D equipment render of Water Softener PlantConceptual 3D render

Water Softener Plant

Ion-exchange softening for reduction of calcium and magnesium hardness.

Explore
Conceptual 3D equipment render of Pressure Sand Filter (PSF)Conceptual 3D render

Pressure Sand Filter (PSF)

Granular media filtration for suspended-solids removal and process pretreatment.

Explore
Conceptual 3D equipment render of Multigrade Filter (MGF)Conceptual 3D render

Multigrade Filter (MGF)

Graded-media filtration for water clarification and downstream equipment protection.

Explore