Bakrol, Ahmedabad, India+91 97277 86892
Enquire
Home/Fabrication & equipment

Fabrication & equipment

Pipe Rack & Supports

Pipe supports and racks developed around routing, loads and thermal movement.

Request technical proposal
Conceptual 3D equipment render of Pipe Rack & Supports
Pipe Rack & Supports — conceptual 3D equipment render. Final configuration follows the approved project design.

3D EQUIPMENT VIEW

Pipe Rack & Supports

Explore the equipment arrangement, then read how the system works and review its technical drawings.

Description & drawings Browse equipment renders

Conceptual equipment render. Final dimensions and configuration follow the approved project design.

PRODUCT DESCRIPTION & TECHNICAL DOCUMENTS

How pipe rack & supports fits your process.

Operating principle

Pipe supports and racks developed around routing, loads and thermal movement.

Fabricated supports carry the defined equipment, piping and maintenance loads. Member design, connections and foundations follow the approved structural design basis.

Engineering checks

  • Operating, empty and maintenance loads
  • Wind / seismic and thermal movement basis
  • Deflection, vibration and stability
  • Fabrication tolerances and foundation interfaces

Configuration & equipment

  1. Base frame / columns
  2. Primary supporting members
  3. Secondary members and bracing
  4. Equipment mounting plates
  5. Bolted / welded connections
  6. Anchors and protective finish

Configuration options are reviewed against the project duty. Supply quantities and final scope are defined in the approved proposal.

Process / operating itemEngineering requirement
Process review 1This is an engineering workflow; support structures do not have a fluid-process PFD.
Operating and maintenanceInspect corrosion protection. Check fasteners and welded connections. Confirm anchors and supporting civil condition.
DocumentationProject-specific datasheet, PFD, P&ID, equipment GA, electrical load list and O&M documentation as agreed.

PDF & DRAWING DOWNLOADS

Keep the technical references.

Read the process equipment brochure, or download the process and arrangement drawings below.

Open brochure (PDF) Download PDFProcess drawing ↓Equipment drawing ↓

ENGINEERING SEQUENCE

Engineering & fabrication sequence

Download drawing (SVG)
Design basis & interfaces → Layout & load review → Detailing & materials → Fabrication & inspection → Installation interfaces
Main process Utility / chemical Residual stream Recovery / recycle

Swipe the diagram to view every stage.

Design notes
  • This is an engineering workflow; support structures do not have a fluid-process PFD.

Indicative process overview. Equipment tags identify functional blocks only. Final PFDs, P&IDs, duties, sizes, valves and instruments are developed from the approved project design basis.

EQUIPMENT DRAWINGS

2D layout & exploded component views.

Review the functional arrangement and the components that make up the equipment.

Pipe Rack & Supports 2D functional arrangement

Reference drawings are not to scale. Project dimensions, equipment duty, pipe sizes and materials are specified after design review.

Download 2D SVG
Pipe Rack & Supports component decomposition reference
Pipe Rack & Supports — component decomposition

EXPLODED VIEW

Understand the assembly.

The separated component schematic identifies the main equipment groups. Vendor-specific internal geometry is established during detailed engineering.

  1. Base frame / columns
  2. Primary supporting members
  3. Secondary members and bracing
  4. Equipment mounting plates
  5. Bolted / welded connections
  6. Anchors and protective finish
Open calculation software Return to catalogue

EXPLORE YOUR DESIGN BASIS

See how operating hours change energy use.

Enter the total running electrical load for this equipment or plant, then adjust its daily running hours.

Illustrative arithmetic using your inputs. These values are not measured plant results or a performance promise.

Daily electricity
80.00 kWh/day
30-day electricity
2400.00 kWh

Energy = electrical kW × running hours. Constant running load; standby load, starting transients and tariff charges are excluded.

Open detailed calculator →

YOUR PROJECT, YOUR DESIGN BASIS

Configure your requirement.

Enter what you know. Leave unavailable values blank for engineering review.

Process inputs

Equipment type, gross/working volume, geometry, dimensions, design pressure/vacuum, temperature, fluid density/corrosivity, MOC, corrosion allowance, lining, supports, nozzles and design code.

Equipment & execution preferences

Materials are reviewed separately for each component against the fluid chemistry, temperature and service conditions. Preferences are subject to technical suitability and the agreed proposal.

No details are sent until you choose a sending channel.

A solution shaped by your requirements.

Pipe supports and racks developed around routing, loads and thermal movement. Process requirements are translated into mechanical design, material selection and fabrication details. Drawings, connections, supports and inspection requirements are agreed before manufacture.

What we review

  • Fluid service, density and chemical compatibility
  • Working volume or design flow
  • Design pressure, vacuum and temperature
  • Material, corrosion allowance and finish
  • Nozzles, supports, loads and site interfaces
  • Applicable design code and inspection requirements

Capacity, materials, operating conditions and performance are specified after review of your project data. Product images are conceptual visualizations.

From design to operation

Our scope can cover process and mechanical engineering, manufacturing, supply, installation, commissioning and ongoing support. The final proposal clearly defines supplier scope, client interfaces, optional items and exclusions.

APPLICATIONS

Connect equipment to your industry.

Review the application, data requirements and candidate treatment options.

Chemical & PetrochemicalAutomotive & EngineeringPower & Boiler Utilities

EXPLORE FURTHER

Related solutions

Conceptual 3D equipment render of Pressure Filtration VesselConceptual 3D render

Pressure Filtration Vessel

Fabricated pressure filtration vessels to an agreed design basis and applicable design code.

Explore
Conceptual 3D equipment render of Vertical Storage TankConceptual 3D render

Vertical Storage Tank

Vertical storage vessels selected for fluid properties, site constraints and loading conditions.

Explore
Conceptual 3D equipment render of Rectangular Process TankConceptual 3D render

Rectangular Process Tank

Rectangular process tanks with project-specific working volume and structural design.

Explore