Bakrol, Ahmedabad, India+91 97277 86892
Enquire
Home/ZLD & water recovery

ZLD & water recovery

Mechanical Vapor Recompression (MVR)

Vapour recompression integrated into an engineered evaporation system.

Request technical proposal
Conceptual 3D visualization of mvr evaporator with vapor compressor
MVR evaporator with vapor compressor — conceptual equipment visualization; final configuration follows approved design.

3D EQUIPMENT VIEW

Mechanical Vapor Recompression (MVR)

Explore the equipment arrangement, then read how the system works and review its technical drawings.

Description & drawings Browse equipment renders

Conceptual equipment render. Final dimensions and configuration follow the approved project design.

PRODUCT DESCRIPTION & TECHNICAL DOCUMENTS

How mechanical vapor recompression (mvr) fits your process.

Operating principle

Vapour recompression integrated into an engineered evaporation system.

Thermal concentration removes water by evaporation and increases nonvolatile solids concentration. MEE, MVR, crystallization and ATFD use different heat-transfer and solids-handling arrangements.

Engineering checks

  • Feed mass flow and full salt chemistry
  • Boiling-point elevation, fouling and corrosion
  • Heat and mass balance with utility basis
  • Condensate quality and final solids route

Configuration & equipment

  1. Conditioned concentrate feed
  2. Heating surface / heat exchanger
  3. Evaporation or drying chamber
  4. Vapour separation and handling
  5. Condensation / heat-recovery interface
  6. Concentrate or solids discharge
  7. Cleaning and control system

Configuration options are reviewed against the project duty. Supply quantities and final scope are defined in the approved proposal.

Process / operating itemEngineering requirement
Process review 1Separated vapor is compressed and reused as a heating medium.
Process review 2Startup heat, non-condensables and condensate handling are designed separately.
Operating and maintenanceTrend heat transfer and fouling indicators. Inspect seals, vacuum and vapour systems. Follow approved descaling and shutdown procedures.
DocumentationProject-specific datasheet, PFD, P&ID, equipment GA, electrical load list and O&M documentation as agreed.

PDF & DRAWING DOWNLOADS

Keep the technical references.

Read the zld & recovery brochure, or download the process and arrangement drawings below.

Open brochure (PDF) Download PDFProcess drawing ↓Equipment drawing ↓

PROCESS FLOW DIAGRAM

Mechanical vapor recompression

Download drawing (SVG)
Conditioned feed → Evaporator heat transfer → Vapor-liquid separation → Concentrate collection → Further solids handling
Main process Utility / chemical Residual stream Recovery / recycle

Swipe the diagram to view every stage.

Design notes
  • Separated vapor is compressed and reused as a heating medium.
  • Startup heat, non-condensables and condensate handling are designed separately.

Indicative process overview. Equipment tags identify functional blocks only. Final PFDs, P&IDs, duties, sizes, valves and instruments are developed from the approved project design basis.

EQUIPMENT DRAWINGS

2D layout & exploded component views.

Review the functional arrangement and the components that make up the equipment.

Mechanical Vapor Recompression (MVR) 2D functional arrangement

Reference drawings are not to scale. Project dimensions, equipment duty, pipe sizes and materials are specified after design review.

Download 2D SVG
Mechanical Vapor Recompression (MVR) component decomposition reference
Mechanical Vapor Recompression (MVR) — component decomposition

EXPLODED VIEW

Understand the assembly.

The separated component schematic identifies the main equipment groups. Vendor-specific internal geometry is established during detailed engineering.

  1. Conditioned concentrate feed
  2. Heating surface / heat exchanger
  3. Evaporation or drying chamber
  4. Vapour separation and handling
  5. Condensation / heat-recovery interface
  6. Concentrate or solids discharge
  7. Cleaning and control system
Open calculation software Return to catalogue

EXPLORE YOUR DESIGN BASIS

See how operating hours change energy use.

Enter the total running electrical load for this equipment or plant, then adjust its daily running hours.

Illustrative arithmetic using your inputs. These values are not measured plant results or a performance promise.

Daily electricity
80.00 kWh/day
30-day electricity
2400.00 kWh

Energy = electrical kW × running hours. Constant running load; standby load, starting transients and tariff charges are excluded.

Open detailed calculator →

YOUR PROJECT, YOUR DESIGN BASIS

Configure your requirement.

Enter what you know. Leave unavailable values blank for engineering review.

Process inputs

Feed flow, TDS and detailed salt chemistry, temperature, upstream RO recovery, target concentrate/solids, boiling-point elevation data, fouling/scaling tendency, condensate target and utility availability.

Equipment & execution preferences

Materials are reviewed separately for each component against the fluid chemistry, temperature and service conditions. Preferences are subject to technical suitability and the agreed proposal.

No details are sent until you choose a sending channel.

A solution shaped by your requirements.

Vapour recompression integrated into an engineered evaporation system. Water recovery is assessed across pretreatment, membrane separation and thermal concentration. Salt chemistry and solids handling determine the feasible operating route.

What we review

  • Feed mass flow and full salt chemistry
  • Feed and target concentrate solids
  • Upstream recovery and concentrate composition
  • Temperature, fouling and scaling characteristics
  • Condensate quality and reuse objective
  • Steam, power, cooling and disposal interfaces

Capacity, materials, operating conditions and performance are specified after review of your project data. Product images are conceptual visualizations.

From design to operation

Our scope can cover process and mechanical engineering, manufacturing, supply, installation, commissioning and ongoing support. The final proposal clearly defines supplier scope, client interfaces, optional items and exclusions.

APPLICATIONS

Connect equipment to your industry.

Review the application, data requirements and candidate treatment options.

Chemical & PetrochemicalAutomotive & EngineeringPower & Boiler Utilities

EXPLORE FURTHER

Related solutions

Conceptual industrial thermal concentration and water recovery plantConceptual 3D render

Integrated ZLD Plant

Integrated effluent treatment, membrane recovery and thermal concentration for ZLD objectives.

Explore
Conceptual 3D equipment render of RO Reject Recovery SystemConceptual 3D render

RO Reject Recovery System

Additional treatment of RO concentrate subject to feed chemistry and scaling constraints.

Explore
Conceptual 3D visualization of multiple-effect evaporatorConceptual 3D render

Multi-Effect Evaporator (MEE)

Multi-effect evaporation for concentrating suitable process and wastewater streams.

Explore